We have all seen it in the movies… the hero has been captured and picks his handcuffs to escape. I recall a time from my youth when I found myself in handcuffs and pulled a staple from a cork board to try and pick the lock. It did not work.
Needless to say this is a skill that takes some practice. Unlike the movies, you cannot just grab a hair pin and pop open your cuffs. The good news is that this is a challenge you can handle. Once you understand how the lock works, you should be able to consistently free yourself.
Also, if cuffed behind your back you should always be able to sit down on the ground and move your bindings to the front. This is the easiest way to break free.
Caution: Never practice picking handcuffs without having two keys within reach. Also, never tighten them down to the point that they cut off the circulation to your hands. You do not know how long it will take you to get your hands free.
Make Your Own Key
When you see people using a piece of wire or a paperclip to pick the lock, they are essentially creating a makeshift key. A paperclip is the perfect thickness to accomplish this as the metal needs to be thick enough to hold its shape.
Step 1) Straighten out your paperclip or thick wire
Step 2) Insert the end of the wire into the keyhole and bend it to the side.
Step 3) Insert it further and bend it back the opposite direction so you create a zigzag in your metal.
Step 4) Twist the metal just like you would with a key. Be patient. You may have to wiggle it a bit or twist in the other direction to get the cuffs to pop free.
Step 5) Remember to hold onto your key to free your other hand. You would not be the first person to make the mistake of discarding it too quickly.
Some handcuffs are double-lock models. This means that they have to be released in two different directions before the cuffs can be released. The only difference with this is that your key needs to be twisted in both direction before you will feel them click loose. It should still be fairly easy to escape from this type of model.
Make a Shim
A shim is simply a thin piece of flat metal that is used as a barrier between the teeth of the cuffs. A good shim must be flexible and should be no thicker than a credit card. The metal clip from an ink pen can work, but my favorite shim is made from cutting a square out of the side of an aluminum can..
Step 1) Insert your shim into the opening where the teeth slide into the rest of the cuff. You want your shim centered on the teeth with any excess metal wrapping around the sides.
Step 2) Wiggle and push the metal in as far as it will go without pushing so hard that you bend the metal. It is important that your shim stays flat.
Step 3) Simultaneously apply pressure to the shim and tighten the cuff by one tooth. You should be able to feel and hear it click in place. If you do this right, the mechanism will drop on the shim instead of the tooth.
Step 4) Push and wiggle on the shim being sure not to let it back out of the mechanism. The cuffs should come free.
Escaping From Alternative Handcuffs
Anymore many captives find themselves being bound by something almost as convenient and strong as handcuffs, but much less expensive. Zip ties and duct tape are two examples that are commonly used. The key to escaping either of these bindings is outward pressure.
Step 1) Raise your hands as high as you can being careful not to let the edge of the duct tape roll. You do not want to wiggle your hands back and forth as it will turn the tape into more of a rope. This makes it stronger. The weak point is the exposed edge.
Step 2) Practice a downward motion striking yourself and ripping your hands apart. You will only get one shot at this so you have to get it right. If your hands are bound in the front, bring your hands down across your chest or belly. If they are bound behind your back, bring them down on your butt or move them to the front. When practicing, do not actually make contact.
Step 3) When ready, raise your hands and bring them down as fast as you can. Strike your body hard and rip outward when you make contact. If done correctly, this should rip the tape breaking your hands free.
Step 1) Move the square plastic lock on the zip tie to be centered between your hands.
Step 2) Tighten the zip tie as tight as you can get it.
Step 3) Unlike duct tape, you do not have to worry about rolling the edges and making the binding stronger. However, thick zip ties may have to be weakened by rubbing them on a sharp surface. You can find the edge of a table or door to get the process started. Try to focus on the plastic lock holding the zip tie together.
Step 4) Just like with the duct tape, you will raise your hands as high as possible and bring them down swiftly striking your body. When you make contact you will rip outwards popping the lock on the zip tie.
Note: This works even if one zip tie is used for each hand or if a third is used in between. You can also use a shim to break the zip tie lock free, but it has to be narrow enough to fit inside the plastic square.
I always replace my boot laces with 550 paracord, and this is one of its best uses. If you are having trouble getting out of zip ties or duct tape, you can saw your way through. To do this you need to pull one lace out of your boot and tie a loop on each end. Put a loop over one foot, drape the cordage over the bindings, and then put the other loop over the other foot. Then just saw back and forth with your feet until the friction breaks through the bindings.
Want a Shortcut?
If you want to be sure you can get out of your handcuffs, there are several products you can buy to help you. I like to have a lock pick kit with me as much as possible so I can get through any lock. It includes a shim and a handcuff key, so it has all my bases covered.
You can also buy some spy level gear to help you get free. There are pieces of jewelry like pendants and rings that have shims or handcuff keys built in. Most people would never think to look that closely at these items. There are also boot laces that you can buy that have a hidden handcuff key in the tip.
Want to Practice?
There are several ways that you can practice these techniques. The least expensive and easiest way to test your skills is to start with duct tape and zip ties. This is a lot of fun, and it’s easy to get the whole family involved.
When it comes time to move on to handcuffs, a normal set is fine. However, it may require several attempt with a helpful assistant to get you free. The easier way to learn is to get a see-through set of cuffs so you can see that movement in the mechanism. Handcuffs are quite simple and seeing the movement is very helpful during the learning process.
Once you master handcuffs, you may want to get a lock pick set along with a see-through padlock so you can further your skills. When SHTF, having the ability to get through almost any lock or door will be very helpful and could save your life.
I would be remiss if I did not give some advice about escaping from handcuffs. Getting out of your cuffs when in police custody is a good way to get shot. In addition COPS get you into the back seat of their car as quickly as possible, so getting the cuffs to the front is very difficult. I would only ever remove police cuffs if you feel that your life is in danger.
In hostage situations, this can be just as dangerous. Remember that trying to escape from a captor is the most dangerous move you can make. I would only suggest freeing yourself to escape if you know for sure that you can break free or if you know for sure that your captor is going to kill you. If there is any question, wait it out to see if your situation changes. If nothing else, this is a fun party trick to show your friends.